Garage Related Questions

Craftsman garage door opener won't engage 
I set up my Craftsman garage door opener and the trolley moves in the down position and then stops and never engages with the arm
The manual that came ...

Guardian Model 21230-L  
Our door won't open or close when you push the remote, the light flashes 5 times but nothing happens. In the instruction book it says to reset the vacation ...

Garage door stops at 6 inches and 4 ft while going up 
I have 2 garage doors and my wife programmed hers on her side and I tried to program mine on the right side and now the garage door stops at about 6 inches ...

light will not go off 
why is it that the light on genie model 12 a will not go off.

garage door closes instead of opens when safety sensors are activated 
I had installed a 1/2 hp craftman garage door opener. I used the installation manuals and recheck every step shown on the manuals.

The problem is that ...

Programming new remote for 1987 Raynor model 120-7 
I just bought a house that has an old Raynor model 120-7. I can't find the learn button. I bought a couple extra remotes, but can't figure out how to ...

Garage Door Opener lights will not come on 
My lights will not come on, I put new bulbs in and nothing happened; everything else works.
You could check to see if power is getting to the bulb sockets....

sensitivity adjustment? 
My remotes only work if I hold them less than 2 feet from the main motor. My homelink and keyless pad on the garage door also won't work anymore. All have ...

Genie Wireless touchpad 
The Genie Wireless touchpad works and the remote control won't or if I program the remote to work, the wireless touchpad won't. How do i get both to work?...

Reset Code on Raynor remote 
I have lost a remote for my garage doors. If I erase the codes and reset them in the remaining remotes, will they have a different code? My concern is ...

Garage door closes then opens again 
im not sure how this happened but now when I close my garage door it closes then opens again, it wont stay shut. The light on the opener starts blinking....

Chain off track 
Hello,
My son let down the garage door and my daughter's car was not completely in the garage, so the door bumped her car and then went back up. The ...

Power to motor keeps going out 
I have a genie model IMS 1000/A ACSR3G The power on the unit went out so I pulled the power cord, waited a few minutes and the power came back on.

I ...

Neighbors Remote Opens My Garage Door 
my neighbor's opener opens my garage door.

Clear all codes on your opener.

If yours uses rolling code technology (Has a "learn" button) press and ...

Garage door opens but won't close 
I can open it but it won't close with the Keyless entry or remote key.

Will it close when you press and hold the wall control button?

If so, Your ...

genie garage door will not close 
my garage door will open with remote and with wall switch, but will not close with remote and only closes with wall when I hold it down.

It is not ...

Garage Door Opener Motor Does Not Run 
My mother has a Sears 1/4hp chain drive door opener, model 139654200. It suddenly stopped working today.

There seems to be power to the unit, we can ...

Challenger Garage Door Opener model JG850 
My remote quit working and after a few weeks I triggered it while working in my garage and it worked again for about 3 weeks, and now is not working again ...

Garage Door Will Not Close 
garage door will not come down with remote or touch pad
Does the garage door open with either one? Which one?

Replacement for garage door remote control 
We have a garage which was built in 1992. The garage door system was made by Genie Blue Max, and the remote control is out of order. We'd like to get a ...

Garage Door Binds 
We have a new garage door with a torsion spring. When we installed the garage door opener to the door the door would only go down half way and the garage ...

Automatic Garage Door Will Not Open 
I have a model KLIK2 garage door opener. I replaced dead battery. Lights flash when code entered but door will not open. What is my next series of steps....

Garage Door only Closes when I hold Down the Button on the Wall Control 
opener works if I hold the button down continually

but remote closer will not close

It will open but will not close
Problem is with the infrared ...

python 2 garage door opener 
my python 2 garage door opener does not go mp or down
i have power to 118 volts to the box.
but troubleshooting light doesn't light up.
Does it do ...

Remote garage door opener problem 
Sometimes when I use my remote to open my garage door as I'm entering my driveway, the door continues to open and close on its own.

I have to get into ...

Garage Door Stopped Working 
My garage door stopped working. The sprocket does not move and is making a loud noise. I have the 139.53413 model. What would be the cause and would it ...

program car door opener to garage door 
I am trying to program car door opener to garage door. Car owners manual refers to "training button"---where is this located on motor?

It is usually ...

How to set limits 
I have A Raynor Aviator, the limits up and down have gone haywire. can not program.

Genie model 209 Remote 
I have a Genie model 209.

Will a chamberlain KLIK1U work with it?

I can't find any dip-switches.

Liftmaster chain drive or Overhead Door Legacy 
Which do you think is a better garage door opener and why?

Liftmaster 1/2 HP chain drive (3265)

Overhead Door 1/2 HP chain drive Legacy (not the ...

Door Opener Remote
will not Close Door 
My door will open, but will not shut unless you hold the button?

Allister ARD II will not open. 
Hello,
My ARD II will not open. (It closes fine).

It makes a buzzing noise that is coming from a relay looking box on the circuit board. I manually ...

Garage door 
My Sears Garage door opener is not working it will not stay down. One of the sensors is green and the other is yellow. Would that cause it to malfunction?...

replaced light bulb but it still will not come on 
I have replaced the light bulb in the Legacy unit but it will still not come on??
Easiest and least expensive solution is to install a motion detector ...

Opening the Garage Door 
I recently moved in to a new house with Signature garage door openers. The old owners of the house didn't leave the code for the key pad outside. How do ...

Garage Door Won't Close 
My Sears Craftsman garage door all of a sudden will not continue down to the closed position. It returns to the open position and the light blinks indicating ...

Gargare Door Won't Open/Close Automatically 
Hi, my garage door all of sudden won't open or close automatically. The motor runs as usual; however, it's seems to not be connecting or something.

Is ...

Disconnect Garage Door Opener Sensors 
how to disconnect sensors to garage door opener so it can open and close without the sensors -- model no hbw0777

Python Chain Glide 
Please advise where Python door openers are made. I want something made in the USA, and won't accept Chinese manufactured products.

I currently have ...

Allister Acess 3500  
Garage door won't open or close electrically.

It will move 6 or 8 " , then stops, and will go back.
Do you have any suggestions? The electric eye ...

I have a Raynor "Safety Signal" (Model 3265RGD 1/2 HP) opener. 
Both "Safety Signal" remotes stopped working. Both batteries are OK. The unit on our wall still operates OK. I have tried all the "LEARN" steps to re-enter ...

my lights do not come on 
my lights do not come on and i have replaced both bulbs
The simplest and least expensive solution is to install a motion detector lamp in the garage....

1988 Raynor Garage Door Opener  
I am a real estate agent and have a home owner with a Raynor Garage Door Opener that was made in 1988 and the home inspector wrote it up for not having ...

Re-Program Remote Controls 
Just moved into a house and my remote controls don't work, how can I re-program them and also how do I change the 4 digit code for the wireless entry.

Legacy ...

Genie Blue Max Garage Door Opener Remotes 
I have a Blue Max screw drive garage door opener that needs a remote control. I understand this opener is no longer being made. Is this remote available ...

Battery replacement in key pad 
What to do after replacing a battery in key pad with a new battery. I replaced it and tried to open with out changing code. Will not open door.

Thanks ...

KLIK2U wireless keypad  Not rated yet
Is a KLIK2U wireless keypad compatible with a twenty year old Stanley garage door opener.
According to the manufacturer (Chamberlain), it is.

Amazon ...

key pad  Not rated yet
key pad will not open door but will open door
Huh?

Python 2  Not rated yet
When I push the button, the motor buzzes but none of the interior gears move. Have you removed the cover and gone far enough that you can actually see ...

How to change a light bulb  Not rated yet
How to change light bulb? I once knew a professor, a PHD, brilliant in his field, but I would swear he could not change a light bulb.

If you don't ...

Craftsman 1/2 HP won't open or close  Not rated yet
Garage door will not open with unit on wall or remotes, works fine manually makes a clicking noise then light on overhead unit flashes green 5 times ...

Overhead Python2 remote control issue  Not rated yet
I have a 2 car garage both are Python 2. I got brand new 3 button Genie remote control. Both units work correctly from the wall unit to open/close.

I ...

Garage Door opener clicks  Not rated yet
Garage Door opener clicks when the wall button or the remote is depressed. It does not move the chain at all. Can you hear the motor hum? If so, the gears ...

Keyless Entry   Not rated yet
I have a Clicker® Universal Wireless Keyless Entry and lost the programing instructions. How do I change the code on it?
You will find a link to download ...

Motor gets stuck  Not rated yet
I have unlatched the carrier and verified that there is no obstruction when opening and closing the door.

The chain will run for a little then get ...

Changing lightbulb in Overhead Brand Garage Door?  Not rated yet
How do you change the lightbulb?
Open the plastic cover. It is usually hinged at one end and you may need to press it in to clear the retaining buttons....

Broken Garage Door Spring  Not rated yet
how do you open the garage door once the spring breaks?
With difficulty. Most doors today weigh a few hundred pounds. It usually takes more than one ...

Garage Door Opener dip switch code  Not rated yet
Where do I find the dip switch code for an overhead door python chain glide opener?
Are you sure it uses dip-switches? If so, they are on the back of ...

Garage door won't open with remote  Not rated yet
My Lift Master will not open with the remote. The wall switch works. The remote will actuate the light inside the garage but not the door. The green ...

Python 2 remotes  Not rated yet
Where do I find replacement remotes? Can I use any brand or do they have to be python 2?
You can use a Genie Remote Control With Intellicode.

Genie ...

Door Opens by itself  Not rated yet
After putting up the Clicker KLIK2U about every 3 days or so The door opens by itself. Has anyone had this happen?

Should a green light continue to go on and then off  Not rated yet
Should a green light continue to go on and then off and then on again on back of motor unit of Craftsman garage door opener?

garage door opener won't operate  Not rated yet
my garage door opener won't operate, i only get 4 blinks of the light on the opener. its a lynx455 plus.

Universal garage door openner stopped working all the sudden for two of them.  Not rated yet
I have Sears Craftsman 1/2HP Green learn button garage door with using Clicker CLT1 & KRIK1 controler.
When I came back from vacation for three weeks,...

overhead light won't go off  Not rated yet
The light comes on for no reason and then goes off. Five minutes later it goes on again. Door will still open and close

program the garage remote for the car  Not rated yet
I have recently purchased a new car and can not program the garage remote for the car, I looked it upon your manual and it only had directions for hand ...

Will the garage door work without electricity  Not rated yet
Can the garage doors be opened if the electricity is out?
Yes they can. Your door will not open without power unless you pull the emergency release cord ...

service light and constant beeping  Not rated yet
the service light on our craftsman (die hard) garage door opener is on and it beeps constantly. (we just moved in as renters...no manual...any ideas?...

python 2 learn button  Not rated yet
i need to set my opener in car to my garage opener. i don't see the reset button on the python 2 that i'm supposed to press
The learn button is below ...

Garage door only opens a foot above ground  Not rated yet
I have a Challenger 9300 opener. It raises about 12 inches then slams back down. If I assist it past that point on the lift, it will continue up and ...

Commander Safety signal door opener  Not rated yet
I have a Commander Safety signal door opener that appears to get the signal from the remote and the car (red button control light flashes quickly when ...

Garage Won't open or Do not open  Not rated yet
Hello,
I have an old automatic garage door and it stop opening. There is no visible cracks in spring nor I can see any broken parts.

The electrical ...

Program Legacy garage door opener remote  Not rated yet
How do I program my genie remote opener for my legacy garage drive model 496 cd/b?

How to change code?  Not rated yet
Hello,
I have a Clicker® Universal Wireless Keyless Entry System and I was wondering if there was a way to change the code on it?

Universal wall button has no power  Not rated yet
Hi, my wall button has no power going to it, reset the breakers but power seems to come on sporadically to the unit.

It will come on, I hit the button,...

my idrive is jammed  Not rated yet
My pivot arm on my wayne dalton idrive is jammed in the up position. When the door closes the motor makes a humming noise attempting to lower the arm, but ...

clk1 compatible  Not rated yet
will my clk1 work with my Chamberlain mod200dm?
I don't know. Is it on the list that came with your clicker?

warning beeper for dead battery  Not rated yet
how do i turn off warning beeper for dead battery without replacing backup battery
I don't recall if there is any way to do so without completely removing ...

ADX8832 remotes  Not rated yet
I have 6 model #ADX8832 remotes. They work fine, but are missing the slide button. Is there a way for me to purchase 6 slide buttons?
thanks,
Gary
Sorry,...

keyless entry kills batteries  Not rated yet
I have a sears craftsman garage door opener. The Control pad for the keyless entry outside my garage goes through a lot of batteries all of a sudden....

HOW TO WIRE A THREE BUTTON GARAGE DOOR SWITCH  Not rated yet
HOW TO WIRE A THREE BUTTON GARAGE DOOR SWITCH OPEN CLOSE STOP

Even if I knew your garage door opener and switch model, I just don't remember. It has ...

Garage Door Light Stays on and Flickers  Not rated yet
My garage door light is staying on and flickering. What's the cause?
Could be the light socket, the wire connecting to the socket, or the control board....

Garage door sensors compatible with raynor sensors  Not rated yet
is there any garage door sensors compatible with Raynor sensors?
How many wires on each sensor?

For use with the Raynor R160/R260 and some of the ...

Legacy garage door opener sensitivity switches  Not rated yet
how to set the sensitivity switch on legacy openers?

You will find instructions in the owners manual. If yours is missing you can download it from ...

Garage Door Closes 3/4 then opens  Not rated yet
Garage door keeps opening after it only closes 3/4 the way. Closes fine when disconnected and no binding
Go to the questions page and read the first ...

Remote flashes 4 times  Not rated yet
I have a Clickerproducts remote for a Linear LD050 garage door opener. The remote now just flashes 4 lights yellow. It will not open the garage door....

Craftsman 1/2 hp Garage Opener Problem  Not rated yet
I installed a brand new craftsman 1/2 hp garage opener.

I used the remote to open the door but motor is not running or even humming and bulb does not ...

how to program Craftsman  Not rated yet
How to program craftsman Item# 00953754000 Mfr. Model# 53754
I've been disabled for 12 years now and
I do not keep up with all those numbers.

what ...

Craftsman Garagr Door Opener  Not rated yet
When you push button to lower door, it stops going down and the opener lights blink. Also husband say's the green sensor lights are not on when this happens....

CHI garage door opener  Not rated yet
Can you tell me where to find parts for a CHI opener, I believe it is a model 6000? Are they manufactured under a different name?
I believe they are ...

a motion detector for the garage  Not rated yet
we have a security system but now we also want to install a motion detector for the garage. Is this feasable?
Yes it is.

What type of motion detector ...

garage door opener beeps continually  Not rated yet
door opener works . started beeping a month a go .

Garage Door will not close in hot weather  Not rated yet
I have an Overhead model garage door. In any other weather, except hot, it works fine.

In hot weather, I will try to close it either with the remote ...

Craftsman 1/2 HP Keypad Won't Stay Locked...  Not rated yet
I have a 1/2 HP (I think that's what it is), and I've got two openers that both work fine. I also have a keypad for it and I'm able to set a code, or pin ...

temperature goes over 90 degrees garage opener does not work  Not rated yet
When the outside temperature goes over 90 degrees for several days, the garage opener does not work. We have model # PEC R4. Is there a reset button?...

How do I change my keyless entry pin #?  Not rated yet
How do I change my pin without a # key?

What make and model keyless entry do you have?

Genie Blue Max Remotes Not Working  Not rated yet
I have a GENE BLUE MAX the hard wired PB works, but the (3) remotes do not. Checked wire connections, changed batteries with no effect. Is there a reset?...

disengage the door  Not rated yet
I have a Python 2 and had to disengage the door because our electricity went out. How do i engage it now?
Simply push the lever back up. You may have ...

opener code for keypad  Not rated yet
opener code for keypad Just what code are you looking for? What make and model keypad?

garage door operation is erratic in very hot weather  Not rated yet
garage door operation is erratic in very hot weather, what could be the cause(s)? Erratic in what way?

Temperature variations can cause misalignment ...

Legacy Model 496cd/b  Not rated yet
When I attempt to open the door with the garage wall opener, the light comes on and I hear the motor on the unit trying to open but it doesn't. If I continue ...

recent storm - motor will not engage  Not rated yet
I have a chamberlain garage door opener. After a recent storm the unit's motor will not engage when pressing either the wall button or remote. Only get ...

Allister garage door opener model ARD  Not rated yet
we have a allister garage door opener model ARD the receiver was not connected. we don't know how to connect (Red, Black, white) wires to opener
Did ...

reprogram my one button remote  Not rated yet
I've tried to reprogram my one button system but it will not take. I went thru the info on my owners manual but will not do it
First, make sure the battery ...

Remote control for garage door  Not rated yet
My garage door opener will not close my garage door, but opens & closes my neighbors.

I've checked "how to recode remote control" websites to no avail;...

Telectron wiring diagram  Not rated yet
I am looking for a wiring diagram, schematic for the Telectron R-204 A garage door opener. Do you have a copy in stock or do you know where I can find ...

Resetting PIN  Not rated yet
I have Legacy Garage Door Model# 496cd/b.How do I reset a new PIN into my keypad?
Depends on which keypad you have.

My page Garage Door Opener Installation ...

Very old garage door!  Not rated yet
My garage door is both electric and can be opened manually any ideas? The garage door is a wayne dalton garage door opener and was installed before 1992 ...

Garage Door reverses direction as soon as you let go of the button  Not rated yet
When I push the button to open or close as soon as you let go of the button it reverses direction. This is on a craftsman 1/2 horse
If this is when using ...

Raynor Flitestar garage door opener  Not rated yet
I have a Raynor Flitestar garage door opening system and have been experiencing difficulty getting the door to come completely down(even after changing ...

Stanley U-Install Garage Door Opener-Idler Assembly part  Not rated yet
I have a Stanley U-Install Garage Door Opener, Model 1505/1805/3205 I know that they stop making it long time ago but I need to replace the idler assembly ...

Genie Python emergency release  Not rated yet
reset emergency release on Genie Python opener
Simply push the release lever back up. You may have to jiggle the lever or drive chain before it will ...

Phython 2 Garage Door Opener  Not rated yet
Where is the smart button on the python 2 - is it underneath the shell? I don't see it on the outside of the unit

Can you show me a parts diagram so ...

remote for Genie excelerator  Not rated yet
I have a Genie Excelerator....can I program my remote opener Genie 912 to work?
How old is that remote? Does it use dip-switches or rolling code technology?...

wayne dalton garage door  Not rated yet
wire on door left and right side are not tight what to do? need to tighten and how ?

What type of connector does yours use? Some are just clips and ...

red sensor is blinking 4 times  Not rated yet
The red sensor is blinking 4 times. What does this indicate?

I hope this is not a repeat question for you, but I really would like to solve this before ...

reset the memory on wayne dalton  Not rated yet
how do i reset the memory on a wayne dalton 3012 classic drive
Press and release the learn button on the power head. Then within 30 seconds, press and ...

reprogram the keypad  Not rated yet
I changed my keypad battery and am not able to use the keypad to open the garage door. Any suggestions on how to reprogram the keypad?
Look for the ...

Garage door safety sensors  Not rated yet
the sensor on my garage door is red while the other one is green, whats wrong with it?

Nothing. They are supposed to be different colors. The colors ...

Overhead door garage door opener remote programming  Not rated yet
I have a Overhead Door model 20XL garage opener and I have a remote that is not programmed. Can you please give me instructions on how to program this ...

Keypad changing code  Not rated yet
How do you Change the code on the keypad of a apple guardian garage door opener
I am not familiar with that brand, I've never even heard of it.

Anyone ...

Why wont my opener stop beeping?  Not rated yet
Why wont my opener stop beeping?

That could vary depending on which garage door opener you have.

Try reading the owners manual. Nearly everyone ...

Slow blink green light =stuck open limit  Not rated yet
Slow blink green light - meaning stuck open limit. What does it mean and how do you fix it so I can open and shut my garage door automatically. Thank you ...

remote not working  Not rated yet
My remote control stopped working (batteries ok) but the wall control does. How do I fix the remote? My email (removed because of spam bots looking to ...

Garage door won't open-just buzzes  Not rated yet
model number Legacy 496CD/B Unit is almost 6 years old.

Garage door won't open...we can hear it buzz but nothing engaging,

You probably have stripped ...

Overhead Door Legacy - where I can order parts?  Not rated yet
I have a legacy garage door opener the model number is 496 1/3 horsepower.

I need a new plastic puller that goes on the chain. Mine will not hold when ...

garage door won't close all the way it opens back automatically  Not rated yet
use remote control or control panel switch to open.

the door goes down and almost reach the bottom. but it won't close and suddenly is going up again....

Programming 2nd Door  Not rated yet
Hi, I just purchased and programmed a Clicker KLIK2C and I was hoping it could be programmed to work with a 2nd door. I am only seeing instructions on ...

Allomatic electric Garage Door opener  Not rated yet
remotes will not work. changed batteries but still will not open.

Can only open with wall switch. Any suggestions as to what is wrong?

Will ...

makes a clattering noise  Not rated yet
when i open the door in the morning it makes a clattering noise when it starts to open. the rest of the day it's ok. i am told that the door sits too ...

Garage door opener Problem  Not rated yet
My garage door opener works only when keep pressed. If I do not keep it pressed constantly, the light blinks and it stops functioning. The remote also ...

Raynor light not working  Not rated yet
How to program a Raynor Garage Door Light?

I would assume you have tried installing a working bulb.

You can only change the time the light stays ...

klik2/marantec 4500 compatability  Not rated yet
Can you program a Clicker klik2 remote keypad to be used with a marantec 4500 opener?

I don't know.

You can order a Marantec keypad at Marantec ...

garage door clicker KLIK2U programming  Not rated yet
After I programming the clicker KLIK2U, it works fine. Then I found out the door remote is not working. I re-program the remote then the clicker is not ...

Program my Truck for my Garage Door  Not rated yet
How would I program my garage door with my truck

Go to Programming the Homelink Garage Door Opener

If the instructions on that page do not work,...

entry keyless pad code  Not rated yet
How do I change the present code on my entry pad?

Follow the instructions in the manual.

Those available online that I have been able to find are ...

works once, then--no more??  Not rated yet
My new Clicker remote programs fine, works once, then no more?? Please help.

Is this the only remote you have?

What do you mean by "works once"?

Does ...

Garage Door Opener Lights Will Not Go Out  Not rated yet
Lights on unit will not go out.
Blue Max 1/3 HP, screw-drive
S/N 10901P

The easiest, least expensive fix is to remove the bulb and install a motion ...

Challenger 390 Programming  Not rated yet
Instructions say the LED will blink twice after holding and releasing + button and - button for programming. This does not happen....What do I do????

Have ...

Garage Door wont open or close.  Not rated yet
My 1/3 HP legacy overhead garage door, wont open or close to the keypad, remote control, or wall button.

It was working earlier and now it wont work ...

Overheaddoor legacy model 496 quit working  Not rated yet
I have a Legacy Model 496 cd/b and receiver ACS R10 which has quit working after replacing battery in receiver.

The program button on the opener ...

Reprogramming Garage Door Opener Remote  Not rated yet
How do you reprogram remotes. I lost one and have two others I need to change in case some stole it and didn't lose it?

To disable the missing remote ...

Adjust Garage Door Opener Light  Not rated yet
How to adjust light to stay on longer when opening & closing door?
No matter which make and model you have it is in the owners manual.

Find your manual ...

weatherstripping for wooden garage door   Not rated yet
how to install frost king weatherstripping on garage door or on door jams?

Huh! Get a friend that is somewhat handy DIY type to help you.

Raynor open & close limits  Not rated yet
Raynor model RT311-1265SR--- How do you adjust the open & close limits?

Turn the screw 1/4 turn to adjust. Clockwise to increase, counter-clockwise ...

Will Clicker keypad work on Legacy Opener ?  Not rated yet
Hi, please let me know if Clicker Universal Garage Door Opener Keypad compatible with Legacy opener model 1/2 HP 969CB/B, thanks.

Robert

I don't ...

wireless garage door opener  Not rated yet
how do you change the code on a wireless garage door opener, i have lost my instructions

I don't know.

What is the make and model of your garage ...

Universal Remote for my Allstar 3500  Not rated yet
I brought an universal remote for my Allstar 3500.

According to the manufactor's instructions, I am to push the smart button on the Allstar.

After ...

Missing remote opener  Not rated yet
I have a missing remote. Although it may be "misplaced", it is highly likely it that it has been taken.

Anyway, is there a way to disable that missing ...

Garage Door Opens On Its Own  Not rated yet
garage door keeps opening and won't stay down-

This is usually caused by a faulty remote. Either one of those your family is using or one that is stuck ...

Garage Door Opens About 2 Feet  Not rated yet
I have a Liftmaster Formula I, probably 1995 model.

It has been working with out problems for ever.
All of a sudden, when you try to open the door,...

how to change the battery in the Chamberlain formula 1 key pad'  Not rated yet
how to change the battery on the key pad of the chamberlain formula one

When you open the cover to access the buttons on your keyless entry there is ...

Allstar Commercial Garage Door Opener-Which one do I have  Not rated yet
I have an allstar Commercial Vehicular door opener, the s# is c48b87c37 and the ser. is 2l98. Which one is this?

It is hard to believe that it has ...

Status on Order  Not rated yet
need status on an order placed 5/25/2011

order # yhst-91121188150676-2204

You would have to contact the merchant for information.

Garage Door ...

CHANGE THE LIGHT BULBS  Not rated yet
HOW DO I REMOVE THE PLASTIC COVER TO CHANGE THE LIGHT BULBS?

There should be plastic tabs which you have to depress (may need a screwdriver) near the ...

garage door opener Model139.663953  Not rated yet
We can't get our garage door to open or shut.

It just happened today. what is wrong with it?

The opener has 2 lights on the top and they are on?...

clearing (erase) codes on opener  Not rated yet
How do I clear the remote codes on the opener itself? Overhead Door Legacy.

Press and hold the "learn" button for 30 seconds.

Clicker Universal Garage Door Opener Keypad  Not rated yet
I forgot my door opener password, it is a clicker brand.

Is there a way to reset it?

I assume you are referring to your keypad.

You will find ...

Garage Door Opener Light Not Working  Not rated yet
Have a Guardian 21230L whose light bulb is working; I checked it on my torch and everything's fine, only thing is, it won't come on when either opening ...

Remote Frequency sears electric garage door remote  Not rated yet
How do you change the frequency, code on a sears electric garage door remote

Not sure you can.

Do you mean the frequency or the coding?

Need Assistance with Python Overhead Garage Door Operation  Not rated yet
My Garage Door Opens But Will Not Close

Will the door close if you press and hold the wall control button?

If so Your infrared safety sensors are ...

Pilot Raynor garage won't close from remote  Not rated yet
I can't close garage with remote controls, works sparingly. Have to use wall control and hold down until completely down to close

Go to Garage Door ...

overhead door legacy 696 cdb wont close properly  Not rated yet
This is a sporadic problem but is happening at least 70% of the time.

When closing the door, it will stop on its own and go back up at random points....

how do i figure out my dip switch sequence on my genie screw driver  Not rated yet
how do i figure out my dip switch sequence on my genie screw driver

The dip switch settings on the power head (motor assembly) and the remote must ...

reverse saftey sensors  Not rated yet
Can you run your garage doors without the reverse saftey sensors?

No, the system is required by the control board. There is no way to bypass this requirement....

light bulb won't go out  Not rated yet
The lightbulb won't go out after the door goes down on my Genie BlueMax 12A garage door opener. is there a way to set the timer on the light on the garage ...

Garage Door Safety Sensors  Not rated yet
The door comes down part way and then goes back up. One sensor is red and the other green.

Is this correct?

Will the door close when you press and ...

Programming a Clicker wireless keyless entry for Overhead Door system  Not rated yet
I have an Overhead Door Python 2 garage door opener. Was trying to program for a Click wireless keyless entry.

Pushed the Learn Button and now the ...

The remotes will not open or close the garage door  Not rated yet
The remotes, including the car remote, will not open or close the garage door - a LiftMaster 1/3HP unit. The door works with the wall button. When the ...

Garage door opener malfunctioning  Not rated yet
Our garage door opener starts to close the door and then when it's a foot from the floor it goes back up. There is nothing in the way or blocking it. The ...

python 2 garage door opener  Not rated yet
how do I program a python 2 garage door opener

Programming instructions are in the Genie Chain Glide manual. The Genie is identical to your Overhead ...

Door opens but does not close  Not rated yet
My garage's Door opens but does not close.

Go to Garage Door only Closes when I hold Down the Button on the Wall Control and Garage door opens but ...

Chamberlain Garage Door Won't Open  Not rated yet
My chamberlain garage door won't open due to a thunderstorm.

We checked breakers and they are good. We tried reset button but all it does is click ...

Allister Allister All-O-Matic light  Not rated yet
We have A Allister All-O-Matic Mod=RS Electric Door Control. Can you adjust the light to stay on longer and where?

I don't know. Having had very little ...

Automatic garage door on its own  Not rated yet
All of a sudden our 1/2 horsepower craftsman automatic garage door keeps opening on its own. I close it and shortly thereafter will find it up again. What ...

Allstar Model 6500  Not rated yet
I would like to do a straight swap of a failed Allstar Model 6500. What new make and model would be the easiest to swap, with the fewest adjustments, etc....

garage door manaul key pad  Not rated yet
how to change code

Some of these have online manuals available which include instructions.

If I knew what make and model you have I would point ...

wall button works remotes WILL NOT   Not rated yet
i have a 93 genie screw drive the wall button goes up and down no prob. but the remotes wont work .

i replaced the reciever board but that didnt fix ...

Stanley UT200 Garage Door Opener...  Not rated yet
Hello.

I purchased a house with this type of garage door opener. I tried to change to keypad access code but when I got half way through the process,...

Overhead Door Python unit  Not rated yet
I recently purchased a universal garage door opener since my daughter has a car now.

I currently use the remote garage door opener built into my Honda ...

Overhead Garage Door Opener Problems  Not rated yet
Hi,

I am having problems with my Overhead Door opener Model 496. Whether I press the switch in the garage or one of the remotes, the same thing happens;...

Overhead Door Garage Door Opener model 55b closing force  Not rated yet
I have an old Model 55b Overhead garage door. Works fine.

Need to adjust closing pressure/ sensitivity. Can not locate the screw on the unit to adjust....

Chamberlain Liftmaster Formula 1 Garage Door Opener  Not rated yet
I have a 7-year old Chamberlain Liftmaster Formula 1. Intermitently when I close the door it will only close partially, then reverse and go back up.

The ...

Delden Garage Door Opener Remote  Not rated yet
I have an older delden garage door opener and have lost the remote for it.

Can you help me find a remote that will work for it? It is a Delden Pulsar ...

how do i find the fcc id on a 1/2 HP Model ocg800ml  Not rated yet
how do i find the fcc id on a 1/2 HP Model ocg800ml

Beats me!

I've been away from direct invovment in the business for 11 years since becoming disabled ...

garage door will not close  Not rated yet
the garage door will not close unless I either hold the panel on the wall or key pad, The light flickers and the door goes back up.

I have checked ...

Garage Door won't work  Not rated yet
Neither my remote control nor the house control will open the garage door. The red light is not on or flashing, what do I do?

Is the breaker tripped?...

Garage Door Won't Open or Close with Remote  Not rated yet
I just moved into a home that has an Overhead Python garage door opener. The door was working just fine for the first two weeks and then it quit operating ...

Craftsman Garage Door Opener 1/2 hp Won't Close  Not rated yet
My garage door won't close, unless i keep the button from garage held the whole time...opens fine from my remote, but won't close...lights blinking!!

The ...

programming the multi code 4140  Not rated yet
how do you get the multi code 4140 to recognize the receiver?

Follow programming instructions. If this is a new remote the instructions should have ...

what type of garage door opener do i need  Not rated yet
i just purchased a home that has a python 2 garage door opener system. however, the previous owner did not leave me any remote controls to open the door....

Garage Door Opener Release Latch Won't Hold  Not rated yet
The release latch that holds the garage door on the chain drive will not hold weight of garage door.

It was pulled on and it broke free and it will ...

Door wont close unless we hold the button down  Not rated yet
Door wont close unless we hold the button down
Infrared safety sensors are out of alignment.

Go back to the FAQ page and scroll down just a little ...

garage door key pad  Not rated yet
Once I have opened my garage door I'm suppose to be able to just hit the enter key on the key pad to close it. But this has stopped working.

Everything ...

Garage Door Opener Keeps Opening and Closing  Not rated yet
Garage door keeps going up and down..won't stop, had to disconnect, whats the problem?? There are a few possibilities.

1.) Remove the battery from ...

Challenger 9300 Series Garage Door Opener  Not rated yet
I have a Challenger 9300 Series Garage Door system. I replaced the battery in my remote control and the door would open and close and it functioned perfectly ...

Garage door opener remote control  Not rated yet
we just bought a house and we have the marantec 4500 and the seller gave us the genie intellicode remote, i wonder if this one works to the marantec? Not ...

changing code  Not rated yet
How do I change my code on my key pad. model 1140 chamberlain opener
There are currently 2 manuals online for the keypads. The first is for the 740cb ...

how do i change my lagacy garage door code on my key pad  Not rated yet
how do i change my legacy garage door code on my key pad Last time I checked there was only one manual available online.

You will find it at http://www....

Stanley Garage Door Opener Chain  Not rated yet
I think my chain needs tightening on an old Stanley 1/2 hp. How is this done?

python garage door opener  Not rated yet
Who carries the python garage door opener in my area?

Burlington, NC 27217.

Ours is broken and will not work. Don't think there is a need to replace ...

garage door opener opens but won't close  Not rated yet
Hi,

I have your garage door opener Model #3018. I've only had it for a few years and on Saturday it worked going up and then when I went to put it down,...

How to Program Overhead Door Garage Door Opener Remote  Not rated yet
Overhead Door Style 55B Solid State
How to program remote?
Download one of the Genie Manuals from Garage Door Opener Installation Manuals .

Genie ...

Garage Door Opener Light Bulb  Not rated yet
Went to change lightbulb...won't go on. Any information would be great. The easiest/cheapest way to fix this is to remove the bulb and install a motion ...

keyless entry reset  Not rated yet
how do you reset a wayne dalton keyless entry Go to Garage Door Opener Installation Manuals . Scroll way down to the Wayne Dalton section and look for ...

Door moves a little and stops every time you push the button  Not rated yet
Have you ever ran in to this problem? When you push the button the door goes down about 1 inch then stops. if you push it again it goes up 1 inch then ...

I have a delden x150 garage door with 9 dip switches.. remote = liftmaster with 8 dipswitches.  Not rated yet
I have a Delden x150 garage door. On the motor for the garage door I find 9 dip switches.. recently I lost my remote and was told that the single button ...

Garage Door Opener Track  Not rated yet
I need the mounting bracket that attaches to the end of the track.
Call your local dealer or order one made from a sheet metal shop.

This is not something ...

neighbor's keyless entry pad opens our garage door  Not rated yet
Everytime our neighbor uses her keyless entry pad to open her garage door, our garage door opens as well. This started happening when my husband programmed ...

remote replacement  Not rated yet
We have a Blue Max Model # CT90 remote and need to purchase replacements. What should we buy?
Go to Blue Max Garage Door Opener . You will find a ...

Blue Max model 12a owners manual  Not rated yet
Need an owners manual
Good luck. This one is old enough a manual is hard to find anywhere.

You could try going to Genie's website to ask there.

You ...

Home link programming  Not rated yet
Problem programming to GMC truck to model m-4500
Go to my Homelink Remotes page. There is a number to call and there is a link to the page where you ...

light will not go out  Not rated yet
We unplugged our Blue Max and when we plugged in back in the light will not go off. Please Help
Thanks CARREI The easiest/cheapest way to handle this ...

Stanley Garage Door Opener Tube Rail  Not rated yet
Is it possible to buy one section of the tube rail for a Stanley garage door opener? One section of mine broke. The rest of the opener works fine, so I ...

door opener trouble  Not rated yet
door does not shut automatically Is this another case of "my garage door will open but it will not close"?

If so, just scroll down the FAQ page a little ...

Clicker model KLIK2U  Not rated yet
I am having the same problem as others. Lights flash, but the current code no longer works on the pad. Garage doors do open at the wall switch. Have ...

Garage door does not close right  Not rated yet
I put a ceiling in my garage and moved the opener down a little to make room for the ceiling now when i close the door it acts like it is caught for the ...

Power Surge - Garage Door Opener Won't Work  Not rated yet
There was a surge of power that went through my house and now my door opener won't work. None of the lights are on that are on any of the sensors or on ...

Racor Pro HeavyLift  Not rated yet
Your review of the Racor Pro HeavyLift 4x4 PHL-1R says that the system can be installed with a ceiling up to 12 ft. Other reviews mention 8 ft as max ...

compatability with exsisting opener  Not rated yet
I Have a RAYNOR Garage Door opener Model 120-7 ser#02586. I would like to use your Genie GWKPD-BL keyless door pad....is this compatable.....???
TNXS
...

Python 2 garage door opener  Not rated yet
I have a python 2 garage door opener and it will open by remote & keypad but will not close by remote, keypad, or by the push button on the wall. Purchased ...

Overhead Door Legacy  Not rated yet
I have an Overhead Door Legacy 1/3 H.P. 496 CD and recently the remote would open, but not close it. Now the wall switch will not allow it to go all the ...

garage door won't close  Not rated yet
legacy sensor is blinking red. Bursts of 3
Sensors are out of alignment. Adjust the sending unit so the infrared beam is aimed directly at reciever lens....

Genie Garage Remote No Dip Switches  Not rated yet
I have a genie garage door opener which has a smart button and not dip switches. How can i find a remote controller that works?
You are looking for an ...

Garage Door Opener Remote Stolen  Not rated yet
MY GARAGE DOOR OPENER WAS STOLEN AND WANTED TO FIND OUT HOW DO I RESET CODE FOR MODEL 496CD/B
Look in the manual to find how to reprogram your remote....

raynor navigator ?  Not rated yet
How do I reset my raynor navigator garage door opener? What do you want to reset?

Python 2 garage door opener  Not rated yet
I have a two-bay garage, both equipped with Python 2 Model OCG600ML openers. The remote control for one of them starts both openers at the same time. How ...

Purchased House and Concerned About Old Remotes Not Found  Not rated yet
We purchased a house with a Overhead Python 2 garage door opener. We did not meet the previous owners or get the garage door remotes at closing.

We ...

Python chain glide garage door opener  Not rated yet
Replaced dead battery in remote for Python chain glide OCG710. Cannot find the "learn" button on the motor to resync the remote to the opener?
Should ...

Genie Digital Wireless Keypad  Not rated yet
What battery must I get to replace the one for our Genie Digital Wireless Keypad 00001033?

Thanks!

overhead door company, model 55B problem  Not rated yet
model 55B overhead door company, why it stops half way then goes back up?

Genie Wireless/Keyless Remote  Not rated yet
Will any genie wireless/keyless remote work on a legacy garage door opener??
Thanks
Heath Poindexter
No, it has to be compatible with Intellicode remotes...

How Do You Program Phantom Garage Door Opener  Not rated yet
how do you program phantom remote opener

Raynor garage door opener  Not rated yet
Is there a schematic for a Raynor garage door opener that's approximately 15 years old? There's no model or serial number on the opener.
Most companies ...

Allstar MVP opener has slow blinking red light   Not rated yet
My Allstar MVP garage door opener is blinking a slow red light. According to the manual it means that there is a stuck relay. How do I know which one ...

Garage Door Has no Stops   Not rated yet
door will keep trying to close or open unless you hit the button again to stop it

three blinking lights & door won't close   Not rated yet
Garage door will not open and close with remotes. Three blinking lights occur when we try to close door. What does this mean? It is a Linear unit.
I ...

Instructions to change Keypad code and erase memory and re-program   Not rated yet
I have an Allstar Corp Model MVP garage door opener.

Please email to me the instructions to change the keypad code and erase the memory in the garage ...

LITE DOESN'T TUR OFF EVEN AFTER DOOR COMES DOWN  Not rated yet
MY REMOTE WOULD TURN LITE ON WHEN DOOR OPENS AND SHUT IT OFF WHEN DOOR COMES DOWN NOW.. LITE STAYS ON,. CAN'T TURN IT OFF... DON''T KNOW WHAT HAPPENED....

Overhead Door Legacy Keypad  Not rated yet
How do I reset the KEYPAD for my Overhead Door, Series II, Legacy, 1/2 Hp Model 696CD/B.

This is about a 10 year old model and the keypad cover slides ...

where are the codes for my garage door opener  Not rated yet
How do I find the code to my garage door opener?

What codes are you looking for? Perhaps the best answer is to refer you to your Garage Door Openers ...

Python2 door opens automatically on its own  Not rated yet
I have had my opener open the garage door in the middle of the night twice in the past few weeks. In addition, the opener will then not shut by either ...

Craftsman Garage Door Opener Sensor Lights  Not rated yet
On my 3/4 horse Craftsman garage door opener, should both sensor lights be on?

The one on the right (green) is not lit so I am thinking that there ...

Lost Garage Door Opener Remote  Not rated yet
Is there a way to make sure a lost garage door opener remote can't be used to gain entrance to my garage.
Yes, you can clear all codes, then reprogram ...

Wayne Dalton Garage Door  Not rated yet
When I attempt to close my garage door after opening, it will go down approximately 3/4 of the way, then automatically go back up. Have checked sensors ...

Legacy Overhead Door Garage Door Opener  Not rated yet
I have a Legacy Overhead Garage Door Opener.

I don't have the original remote but I have two universal clicker remotes.

How can I program these ...

Raynor Pilot Garage Door Keyless Entry  Not rated yet
We just moved into a new home and it has Raynor Pilot garage door openers.

It also has a keyless entry keypad installed and we can't figure out how ...

Stanley Garage Door Opener Light Won't Turn Off  Not rated yet
I have a Stanley garage door opener mod# 5100.14 and the lights don't turn off after opening the door. Do you know what causes this? I can't find a manual ...

Garage Door Opener Rail Extension Kit  Not rated yet
I have a Genie Aladdin model 1020L opener 1/3 hp it is designed for a 7 ft door but I need to have an 8 or 9 ft high door 9 ft wide. Are there extension ...

Sears Craftsman Keychain Remote  Not rated yet
How do I replace the battery in my Sears Craftsman key chain remote?
Look at the edge of your remote. You should see a small gap where you can insert ...

Remotes not working Chamberlain 1/2 hp  Not rated yet
Elec storm last night, now opener only works with remote. If I'm in open garage and shut the garage door I have to get right next to door for opener to ...

Remotes Not Working  Not rated yet
Electrical storm last night, now opener only works with remote, if I'm in open garage, if shut big door, have to get right next to door for opener to work....

Garage Door Won't Go Down  Not rated yet
The garage door will go up but it will not go down except if I release the lever and move it down manually.
What is most likely the problem?
Will the ...

New Garage Door  Not rated yet
A new garage door comes with spring and reels.
Is there a question? I am just guessing here but I will assume that is a question.

Usually, the door ...

Model 3512 Garage Door Won't Close  Not rated yet
Door only closes about a foot and goes back up. Clicking noise on opener.

This sounds like a problem with your infrared safety beams. They are mounted ...

Swing Door - Garage Door Opener  Not rated yet
Can you recommend a good manufacturer/installer for an automatic garage door opener for swing opening garage doors? In Vancouver, B.C.

Thanks.

Barbara ...

Wireless Keypad  Not rated yet
I have a genie garage door opener which has a smart button and not dip switches. How do I program my wireless pad?
Illustrated instructions are in the ...

How Many Remotes for Overhead Door Legacy  Not rated yet
How many remote transmitters can be used on an Overhead Door Legacy opener?

Can't get my Genie key fob to work on the 2nd or 3rd buttons. The middle ...

Garage Door Opener Wiring Diagram  Not rated yet
do you have a good diagram for the bell switch and the safety sensors?
No, but they are very simple.

You will find illustrations in your Garage Door ...

Garage Door Openers - Changing Programming Code  Not rated yet
How do you change the code for garage door openers?
If you want to erase all codes and reset/reprogram all remotes and keypads, you first Press and hold ...

Garage Door Opens but Won't Close  Not rated yet
My genie remote opens my garage door but nothing happens when I try to close he door, the remote doesn't even have power to the drive. Any help would be ...

Wire Two Three Button Switches for Garage Door  Not rated yet
How to wire two three button switches for garage door?
It has been too many years (12) since I was active in the field. Even then, I had to refer to ...

How Can I Change the Rail Length  Not rated yet
My old garage door opener had a overall length, end of rail mounted over the door to back of motor = 119". the new opener has a length of 124".

I ...

Craftsman 1/2hp Garage Door Opener-Changing Code  Not rated yet
Do you change the code on a Craftsman 1/2hp garge door opener?
Yes, you can change the code.

If you have an old unit utilizing dip-switch technology,...

Safety Eye Sensor Malfuntion  Not rated yet
Why is the safety eye sensor not stopping the garage door from closing?

Its on; and the both of them are on; and green lights are on.

Does ...

remote will not open the door  Not rated yet
My remote will not open the door. I have new batteries and it still will not work.
Is there power to the opener?

Will the wall control button work?...

garage door open problem?  Not rated yet
My garage door can not open completely. It open to about one foot and stop unless I pushed it up at the same time.
Either the opening force needs increased ...

Genie Directlift Screw Drive Opener  Not rated yet
can the genie directlift screw drive opener be used on a single piece wood garage door(standard door with springs, ect)? I currently have a Genie Pro 83 ...

Wayne Dalton iDrive Remotes  Not rated yet
We just purchased a home that has 3 idrive garage door openers. The home was a foreclosure and all of the remotes are gone.

I would like to reset ...

AllStar remote devices  Not rated yet
I have two PDQ AllStar (Model 4120 2 Channel Transmitter) garage door openers.

They are controlled be seperate wall mounted, hard wired AllStar remote ...

wont always work  Not rated yet
wont always work (new batt)
If you are talking about your remote, you should probably replace it.

Changing pin code for phantom garage opener  Not rated yet
We just bought a house and would like to change the pin code
You will have to clear all codes and reprogram all remotes and your keypad.

Instructions ...

Programming in car remote without handheld transmitter  Not rated yet
Do we need the remote to program a car to the door opener? We have two cars & keyless entry that have been programmed for years (until we erased them ...

Problems with remote  Not rated yet
All three garage door openers (with three different remotes) started malfunctioning the same day.

The remotes function only intermittently; one of ...

Raynor #RT311-1465SR  Not rated yet
how to make adjustments for opening and closing
Instructions and illustrations are in the owners manual. You will find a listing of Raynor garage door ...

Garage Door Opener Emergency Disconnect   Not rated yet
I pulled the emergency disconnect. How do i reset it to work again?
Push the lever back up. If it does not engage, you may have to move the chain a bit ...

What Lubricant to Use with Liftmaster Opener  Not rated yet
What, if any, lubricant should I use on Liftmaster drive gears.
There is a special lubricant for these. You can find it at Lubriplate AERO 3/8oz. Multi-...

GARAGE DOOR OPENER KEY PAD  Not rated yet
Is there a way to reprogram the outside keypad code on a Liftmaster garage door opener?
You will find instructions at http://www.liftmaster.com/consumerweb/...

Legacy Overhead Door Garage Door Opener   Not rated yet
I have a Overhead Door Opener Legacy Model 696 CD/B. It has power but will not work. The sensors are red & green and I have power at the plug. Any thoughts?...

Legacy Garage Door Opener Remotes  Not rated yet
Have two remotes on Legacy opener, both stopped working at the same time.

They will not accept a reprogram.

Will the door open or close when you ...

How do you program more than one remote?  Not rated yet
How do you program 2 genie universal garage door openers?

We have 2 but can only program one at a time. When we program the other, the new one is programed ...

LED Light is Slow Blinking on MVP Opener  Not rated yet
I have an MVP opener and the red led light is slow blinking. I read it was a stuck relay. There are 3 relays in it. Which one do I need to replace? Since ...

Raynor door goes up but not down unless i hold the button  Not rated yet
Raynor garage door goes up but not down unless I hold the button. Whats wrong?
The safety sensors are out of alignment (most likely), or they have gone ...

Where are the code numbers  Not rated yet
where is the code numbers on the unit?
Go to http://www.garagedooropenerguide.com/installationmanuals.html to find your online manual for illustrations ...

Sensitivity - Wayne Dalton iDrive Garage Door Opener  Not rated yet
How do i set the sensitivity of the idrive with the remote wireless station?
I am not sure I understand the question, but then I have been disabled for ...

Update controller and remote to rolling code?  Not rated yet
Please advise. I have Model 55B Overhead door in great condition and I have need of 2 more remotes. Is it feasible to update my system so that I can ...

Smart Button Marantec 4500 Garage Door Opener  Not rated yet
where is the smart button located on the marantec 4500
It is usually located on the back side of the motor assembly.

Owners manuals can be found at ...

remote opens but does not close door?  Not rated yet
The remote control on model 3BTM-0372C opens the door, but when pressed to close the door the light bulb blinks and the door does not travel down.

The ...

Garage Door Will Not Close  Not rated yet
my door opener is 16 yr old it is a screw drive never had any trouble with it

yesterday it stopped working

it went up and now it wont go down

is ...

Overhead Door 4060L remotes not working  Not rated yet
We have an Overhead brand 4060L garage door opener and today, all 3 of our remotes stopped working.

I checked to see if one of the kids locked the ...

python 2 1/2 hp. mod. ocg800ml  Not rated yet
door opens and wont stay up all the way

slides down about 10 to 12 inches

have to do 2 to 3 times to stay all the way up. whats the matter?

Garage ...

Hook Up Wiring for Old Overhead Garage Door Opener   Not rated yet
i have a real old overhead garage door opener

i don't know which wire goes where

it says/ button /photo /light/24vdc/?

Overhead Door products ...

Replace Gears In Craftsman Garage Door Opener  Not rated yet
I have a craftsman 1/2 hp garage door opener - the plastic gear is worn

how easy is it to replace that - do it yourself?

Looks pretty tricky taking ...

Need to Clear Codes and Reprogram Remote  Not rated yet
i have a delden x150 garage door and my opener is a linear.

The second remote was stolen and i would like to change the code, how do i do this?

The ...

Garage Door Will Not Open  Not rated yet
On my Legacy the garage door would not open..Their are two indicators on both sides of garage door inside..One is red and the other has a green light...I ...

Lightbulb Doesn't Work and Door Won't Stay Closed  Not rated yet
2 questions re my Python garage door opener:

1) I have put in a fresh bulb but it won't go on. I saw that you earlier said this might be a relay board ...

Garage Door Will Not Close  Not rated yet
My garage door goes down about a foot than goes back up and the light starts flashing, there is nothing in the way and the beams are showing a green light....

change the light bulb  Not rated yet
How do you change the light bulb on the legacy? I can see the lightbulb but can not get the cover off,

Hi Linda,
See figure 10-1 in the manual (have ...

Remote was Stolen  Not rated yet
I have a legacy garage door model #496cd/b 1/3 hp

The remote was stolen, need to install new code. can you please help me?

Yes, you need to erase ...

Marantec 4500 Garage Door w/keyless entry system  Not rated yet
I recently had to unplug my garage door motor then plug it back in but now the keyless entry system will not work.

I have cleared the code, changed ...

Program Remote Control  Not rated yet
How do I re-program my remote since I had to use a new battery? The new battery does not open the door remotely. Thank you for your help.

Transmitter Mystery  Not rated yet
My Garage door will only go down when working with the transmitter (old one or the new one). It will only respond with movement in the down direction....

Garage Door Won't Close  Not rated yet
Why doesn't my remote to my garage door opener close the door and why

In order for it to close, do I have to hold down the button the whole time while ...

Sear Craftsman 139.53930DM  Not rated yet
Power to the powerhead but no power coming out to sensors, light or controller. Any ideas?

Garage Door Will Not Open  Not rated yet
my garage door will not open, it will start then stop. whats wrong??

Genie Blue Max Garage Door Opener  Not rated yet
what size motor is the model ct 90?

Genie 2020L Sensor Malfunction  Not rated yet
Have a Genie 2020L opener and the sensors seem to be malfunctioning. Sometimes the lights on BOTH sides are off; or red is blinking 3 pulses (indicating ...

Craftsman Mod. 53930D  Not rated yet
Garage door opener has stopped working automatically. One of the sensor lights appears to be out - light in ceiling unit (power head) blinks.

How to program the Allister Model ARDIIA to a Homelink.  Not rated yet
How to program the Allister Model ARDIIA opener to a 2007 Toyota Camry Homelink system? Program the remote?

New home - New remote  Not rated yet
Purchased new (FORECLOSED) home however the phantom door opener does not have a remote.

Purchased 2 universal remotes but the phantom does not have ...

Change Garage Door Opener Light Bulb  Not rated yet
how to change light bulb on my opener

My Stanley Garage Door System is Having Problems  Not rated yet
basically the model number is :ET380C . A08

I pressed the remote for garage door to open and is now stuck in the open position. Normally the back ...

Legacy Garage Door Opener Will Not Open  Not rated yet
My Legacy won't raise: Motor just hums

Garage door only opens/closes sporadically  Not rated yet
When using the remote opener in my car or my hand-held devise the door only opens/closes sporadically. It works fine using the button on the wall. What ...

One of my garage doors stopped working  Not rated yet
door openers stopped working on one and will not reprogram. How do you reset. I tried unplugging from the wall but that didn't work either.

Hi Brad,...

How to wire garage door sensors  Not rated yet
How to wire garage door sensors?

Hi David,

You should download the installation manual for your garage door opener. If yours is not online, use the ...

how to reprogram keyless entry passcode  Not rated yet
how to reprogram keyless entry passcode for craftsman model 139.53684 keyless entry

Craftsman model 139.53918 smart control not working  Not rated yet
I have a craftsman model 139.53918 belt opener. hand remotes work fine, however the smart control light went blank and it will not open the door.

If ...

light on garage door opener no longer turns off  Not rated yet
light on garage door opener no longer turns off after automatically coming on after door is opened or closed The easiest and least expensive solution is ...